​Daily maintenance and maintenance of round bottle labeling machine adjustment


The mechanical operation is generally connected to the power supply, and the relevant actions are coordinated and adjusted in the manual state.

1. Conveying mechanism: Adjust the conveying mechanism to ensure that the product can be smoothly conveyed to the labeling position and sent out smoothly. Generally, the left and right sides of the conveying mechanism are adjusted for products. For the operation method, refer to the relevant chapters of the adjustment section, the conveying of the labeling part and the receiving part The adjustment uses the same method.

2 Labeling position adjustment: Place the product to be labeled under the label peeling board, adjust the labeling head up and down, front and back to ensure that the label peeling position is aligned with the labeling position; adjust the guiding mechanism to ensure that the label is attached to the designated position of the product; combine the above two Ways to adjust.

3 Position adjustment before and after labeling: control the sequence of labeling through the advance or postpone detection of the measuring object; control the sequence of labeling through the labeling delay adjustment; control the length of the second label through the stop delay . Combining the above three methods, adjust the label to the accurate labeling position.

 

One, keep and clean

1. Replace the insurance. This equipment uses AC power, and a fuse must be used to prevent overload.

2. Cleaning mechanism, friction roller cleaning mechanism, use alcohol to clean the mechanical parts that need to be cleaned; clean the electrical box, use commercial neutral cleaning fluid.

Things to pay attention to when cleaning:

l Do not use cleaning tools that damage the surface of the machine;

l Do not use corrosive plastic utensils;

l Do not use acidic solution.

3. Routine maintenance

      The The design of the labeling machine is very easy to adjust, but you still need to check regularly to confirm that the conveying of the tape is accurate (in the case of multiple uses); p>

       According to the different environment, you need to check the machine periodically to maintain the normal operation of the machine;

      Clean up discarded paper scraps and debris.

Remove oil residue from the drum and edges;

Use a soft brush or cloth to clean the lens of the sensor.

4. Maintenance

       this postThe parts of the marking machine are chrome-plated and have anti-rust function. However, during the placement process, you still need to pay attention to anti-rust. Use anti-rust oil to spray all stainless steel and iron parts. Wipe evenly with a soft cloth, {Ohm-40 anti-rust oil}

RELATED NEWS


What should I do if the flat labeling machine fails?

The center of the brush is aligned with the label and the two sides are symmetrical. The marking brush is perpendicular to the surface of the container. The overlap gap of the pressure brush sweeping the container is: a single pressure brush is 10mm-15mm, and a combined pressure brush is 5mm-10mm. The distance between the cleaning brush and the sponge is 1mm~2mm. Adjustment of the pressure bottle head. The press head should be 20mm lower when there is no bottle than when there is a bottle.


​Daily maintenance and maintenance of round bottle labeling machine adjustment

1. Conveying mechanism: Adjust the conveying mechanism to ensure that the product can be smoothly conveyed to the labeling position and sent out smoothly. Generally, the left and right sides of the conveying mechanism are adjusted for products. For the operation method, refer to the relevant chapters of the adjustment section, the conveying of the labeling part and the receiving part The adjustment uses the same method.


Declaration of safe use of labeling machine

Safety statement for labeling machine Please follow the safety instructions to use the equipment, which can ensure the safe use of the equipment for several years and keep the equipment in good working condition. The company will not bear any responsibility for problems and equipment damage caused by improper use and unsafe use of the environment. .


​How to avoid express delivery slips from being infected by details?

In 2020, at the beginning of the year, a sudden disaster broke out in the beautiful city of Hubei. The speed of silent contact and physical transmission spread rapidly in Hubei. Just a few days have made the past prosperous. Hubei Province, with its outstanding talents, has been dimmed. High warnings have sounded in all provinces and cities, and the nationwide anti-epidemic action has kicked off.


​Functions and features of automatic flat labeling

There are many types of labeling machines on the market. The labeling machines have many functions and strong operating skills. How can I choose the right equipment model according to my company's products? How to know which equipment is suitable for mass production?


Fully automatic double side labeling machine structure

Technology continues to develop at a high speed, leading the continuous improvement of industrial technology, and fully automatic technology has replaced traditional manual services in the service industry. The launch of the new model has brought efficient, energy-saving, and systematic management service models to the service industry. How does the industry choose suitable fully automatic equipment? How to efficiently improve production efficiency!